Tennessee § 54-10-104 - Classes and specifications of roads — Working and grading.

Full text of Tennessee Tennessee Code Annotated § 54-10-104 — Classes and specifications of roads — Working and grading., with citation guidance and answers to common questions.

§ 54-10-104. Classes and specifications of roads — Working and grading.

All roads laid off and worked under this chapter shall be known and classified as roads of the first, second, third and fourth class. Roads of the first class shall be not more than one hundred feet (100') nor less than twenty-four feet (24') wide; roads of the second class, not more than forty feet (40') nor less than eighteen feet (18') wide; roads of the third class, not more than thirty feet (30') nor less than fourteen feet (14') wide; and roads of the fourth class, not more than twenty feet (20') nor less than ten feet (10') wide. All roads of the first class shall have worked a roadbed of at least twenty feet (20') as the minimum width for first class roads, sixteen feet (16') for roads of the second class, twelve feet (12') for roads of the third class, and eight feet (8') for roads of the fourth class; and, in constructing the roadbed, concrete, broken stones or gravel or other material approved by the department of transportation shall be used, when concrete, broken stones, gravel or other approved material can be conveniently obtained, to form the surface; provided, that where it is possible and practicable, the roadbeds shall be graded with a fall of one inch (1") to the foot from the center of road to the ditches. Overseers shall also maintain ditches at each side of the roadbed adequate to drain the roadbed. The county legislative body may require sections of roads near populous cities to have roadbeds graded to any width not beyond the maximum width allowed in this section for all roads of the class; and when the condition of the road requires it, timbers shall be employed to construct the roadbed in whatever way the commissioner may direct, and, if practicable, the commissioner may have wet or spouty places underdrained by tile draining. Acts 1891, ch. 1, § 26; Shan., § 1619; mod. Code 1932, § 2729; impl. am. Acts 1959, ch. 9, § 3; impl. am. Acts 1972, ch. 829, § 7; impl. am. Acts 1978, ch. 934, §§ 7, 36; T.C.A. (orig. ed.), § 54-904; Acts 1981, ch. 264, § 12. Cross-References. Width and character of highways in municipalities, § 54-5-202 . Textbooks. Tennessee Jurisprudence, 2 Tenn. Juris., Appeal and Error, § 30. Cited: Vinson v. Nashville, C. & S. L. Ry., 45 Tenn. App. 161, 321 S.W.2d 841, 1958 Tenn. App. LEXIS 120 (Tenn. Ct. App. 1958).

Source: official Tennessee text · Last verified 2026-08-27

Frequently Asked Questions About Tennessee § 54-10-104

What does Tennessee Code Annotated § 54-10-104 cover?

Section 54-10-104 ("Classes and specifications of roads — Working and grading.") is part of the Tennessee Code Annotated, the codified statutory law of Tennessee. It sets out the legal rule or procedure described in the text above. Statutes are amended regularly, so always verify against the official source.

How do I cite Tennessee § 54-10-104?

A common citation format is "Tennessee Code Annotated § 54-10-104" (Tennessee). Legal writing may require the code abbreviation, section number, and year or edition. Match the style required by your court, professor, or publisher.

Is this the official text of Tennessee law?

No. This page is for research and education and may not include the most recent amendments. For official current law, check the Tennessee official source linked on this page or consult a licensed Tennessee attorney.

How does Tennessee § 54-10-104 apply to my situation?

Statutes are interpreted in context, and application depends on your specific facts. Only a licensed attorney in Tennessee can advise on how this section applies to you. Contact your state or local bar association for a referral.

Sources & Verification

Not legal advice. Verify against the official source and consult a licensed attorney in Tennessee.